The problem of lack of fresh air in a private house is standardly solved by properly arranging an air exchange system. Thanks to her work in the housing, the microclimate will always be ideal for work and leisure. For stable operation of the system, installation of ventilation on the roof, which enhances the draft in the exhaust pipe, is required.
Through the ventilation outlets on the roof, the exhaust air with moisture generated during human life is utilized. The speed of air movement in the system largely depends on them. The greater the draft, the more efficient the ventilation.
In the article we present, you will find detailed information about the device of the outputs of ventilation communications to the roof. You will learn how to install and fix them correctly. Independent home craftsmen will receive valuable recommendations.
Ventilation Output Functions
In one- and two-story houses, exhaust ducts from the kitchen, bathrooms, showers, pools, technical rooms (laundry, drying room, the room in which the boiler is installed) and the basement are displayed on the roof through the attic or attic.
According to the requirements of the regulations, in ventilation it is impossible to combine air ducts leading from the kitchen and bathrooms neither with each other, nor with the chimney into one channel. Therefore, usually several vent pipes and a chimney are routed through the roof of the house.
It is permissible to lay them in separate channels in one ventilation shaft. The duct from the basement is usually carried out along the facade of the building and also has a separate exit.
In most cases, it is advisable to combine all the ventilation outlets and pipes into one box, since it is easier to cut and seal in the roof one large hole for the box than several smaller holes for pipes
The correct calculation of the ventilation output is the key to good traction. Natural draft is formed due to the difference in air pressure between the street and inside the chimney.
It is necessary to take into account the height of the ventilation riser, the correspondence of the diameter of the air ducts inside the house to the length of the exhaust pipe, its location on the roof. The higher the ventilation pipe, the stronger the draft will be in it. Strengthen the draft will help the ventilation installation on the roof.
To close the rain access above the outlet of the pipe or duct, an umbrella is mounted. This is the simplest kind of deflector, working well in areas with high and medium wind loads. With gusts of wind inside the duct, a vacuum is created thanks to it, greatly enhancing traction.
In natural air exchange systems operating in areas with low wind activity, a turbine deflector is installed at the mouth of the hood. Such a device is able to increase traction even with a slight blow of a virtually imperceptible breeze.
In addition to protection against all types of external pollution, any type of deflector prevents the air flow from capsizing due to the lack of traction in the pipe.
The best way to increase traction is to install a turbo deflector. Its head rotates from the wind, due to which the vacuum in the ventilation duct is significantly enhanced
Thus, it depends on a properly arranged ventilation outlet:
- the presence of good traction in ventilation ducts;
- good air exchange in the interior;
- lack of smells in the house;
- humidity reduction in wet rooms (bath, laundry, shower).
If the width or height of the ventilation outlet was not calculated correctly, draft may disappear in the ducts or reverse draft may occur. In this case, in addition to the deflector, it is also desirable to put a check valve, which excludes the reverse movement of the exhaust air mass.
Ventilation duct assembly
The ventilation through passage on the roof is a pipe made of metal or plastic, which is placed in an opening in the roof. The pipe is fixed in a metal cup. After its installation, the hole is sealed and insulated from the outside and from the inside. The duct connects to the bottom of the unit, and a deflector is installed on top.
It is more convenient to use the finished factory shaped product for mounting the ventilation duct passage. Manufacturers of ventilation systems offer many models that vary in design, shape and color. For each type of roof, its own types of ventilation pipes are developed.
Steel galvanized pipes wrapped in a layer of polypropylene are in greatest demand. At the bottom of such a product is a seal, and on top is a cap with a deflector.
Do not combine the duct outlets into one, otherwise, in the event of adverse weather conditions, unpleasant odors will spread as a result of the back draft
The mounting features of the ventilation duct passage assembly depend on a number of factors:
- on the type of roof - complex or flat, single or gable;
- from roofing material - metal or ceramic tiles, decking, soft tiles, etc .;
- from the angle of the pitched roof.
Sealing and warming of the roof at the installation site of the passage element must be carefully performed. If this is not done, through the junction of the coated pipe into the insulation layer of the roofing cake and into the room will get moisture, which will cause the destruction of structures.
The junction of the ventilation pipe with the roof must be carefully sealed. Sealing is carried out by applying a water-repellent material to the passage and applying silicone sealant under the ventilation outlet flange
What are the main requirements for the passage node:
- pipe outlets must be strictly vertical so that the air does not encounter obstacles when moving upward;
- for each duct - from the kitchen hood, from the sewer riser, from the bathrooms there should be a separate exit to the roof;
- the best option is that the exhaust exits pass close to the ridge edge of the roof, but so that the run is not disturbed and the entire rafter system resting on it is not weakened;
- Selected shaped products should ensure unhindered movement of air masses and tightness.
The main element of the passage unit is the outlet - shaped product: a pipe with a flexible metal base made in the form of a flange. It is pressed against the roof covering, giving the relief of the roof to which it is mounted. During the installation, the geometry of the roofing materials used is achieved and the unit is perfectly sealed.
On sale you can find different types of shaped products that facilitate and accelerate the installation of the ventilation outlet on the roof. It can be purchased separately - an outlet for the hood, separately - for sewage, etc.
Roofing: proper installation will ensure complete tightness of the roofing cake
There are several varieties of passage elements:
- Valveless / with valve. Valveless models are perfect for arranging ventilation outlets in a private house. Valves are more suitable for industrial buildings.
- With insulation / without insulation. In cold regions, it is better to choose a ventilation outlet with thermal insulation. Moreover, insulation is necessary if the pipe is placed close to the cornice. In regions with warm winters, an option without insulation will suffice.
- With manual and auto control. The choice depends on the design budget.Very popular among owners of private houses are products with a cable for regulating air circulation.
For the device for ventilation penetration, you can not buy a similar part for the chimney, since they implement fire protection that is unnecessary for ventilation outputs.
Installation and Mounting Recommendations
You can do it yourself on the roof of the ventilation outlet. The installation location of the pipe should be chosen so that it could, if possible, pass through the attic without turns. At the same time, it must not cross the rafters, and especially the ridge run.
The best option is when the outlet of the ventilation pipe is directly above the internal riser of the ventilation shaft or duct. If this is not possible, a corrugated pipe can be used for connection.
The pipe must be connected to the riser strictly vertically
When placing pipes or an exhaust duct, the smallest permissible distance from the supply air intake must be taken into account:
- horizontally - 10m;
- vertically - at least 6m.
The height of the ventilation pipe is determined as follows:
- if it is located near the ridge, the final opening of the hood should rise half a meter above the ridge;
- if the ridge remains from one and a half to three meters, the hole should be flush with it;
- if the pipe is located further than three meters from the ridge, the hole is discharged on the side of an angle of 10 degrees to the horizon with the top on the roofing ridge;
- if the ventilation outlet is near the chimney, the length of the pipes should be the same;
- on a flat roof, the height of the pipe is calculated according to a special table, but it should not be lower than 50cm.
When installing the pipe on a pitched roof, the ventilation outlet should be placed as close as possible to the highest point of the roof - the ridge. In this case, the largest part of the pipe will be in the attic or attic space, will be protected from strong temperature extremes and gusts of wind.
The height of the ventilation pipe to the roof is selected depending on the distance from the ridge. These conditions must be observed so that the outlet is not in the backwater area.
For a flat roof, the main role is played by the geometry of the air duct, which must be located directly under the exhaust pipe so that the air freely exits onto the street.
Installation of ventilation outlet
Installation of the ventilation outlet is carried out in accordance with a previously developed exit location scheme. Installation features depend on the type of roof and pipe construction. In the configuration of shaped products, there is always an installation instruction.
The passage assembly must be carefully sealed on all sides. Factory-made products are usually equipped with everything necessary to ensure complete protection against water.
In general, the installation is performed according to the same algorithm:
- At the pipe exit, marking is carried out corresponding to the diameter of the hole. If there is a template in the set of the passage element, the marking is applied according to the template.
- A hole is cut out in the roofing pie with a chisel or scissors for metal: in the roofing material, in the layer of waterproofing and insulation.
- The sealant is attached with a liquid sealant.
- A walk-through element is placed on the gasket and fastened with screws to the roof. The base of the passage must be attached to the roof as tightly as possible.
- The duct pipe is attached to the passage element and fixed with screws. When working, it is advisable to use a plumb line or a building level to fix the pipe vertically.
- From the attic side, the outlet of the duct to the roof is sealed.
The outlet of the ventilation pipe is the most technically vulnerable unit in the entire ventilation system in the house. It is especially important here not only to solve the aesthetic problem, but also to provide reliable waterproofing of the passage with preserving the properties for the entire life of the roof.
To increase traction in the ventilation system, a deflector is always put on the head of the vent pipe. A deflector is a nozzle in which, under the influence of wind, rarefaction of air masses occurs. Thus, the aerodynamic resistance to flow is reduced.
When choosing a deflector, you need to take into account the climatic features of the region. A number of manufacturers achieve the same goals by equipping an umbrella with an electric fan
So the deflector acts as a traction amplifier. In addition, the exhaust device:
- protects the ventilation system from precipitation;
- prevents the wind from blowing inside the vent pipe;
- prevents the phenomenon of backdraft.
The principle of operation of any type of deflector is based on rarefaction of the air mass at the mouth of the ventilation duct, as a result of which the exhaust air rapidly moves in its direction without mechanical impulse.
Types of vents for ventilation systems
To date, the following types of deflectors are used:
- TsAGI with diffuser - expansion of the ventilation duct: the most efficient design when the wind flow is more than 2 m / s. The design consists of a lower glass with an extension at the end, a cylindrical steel casing, an umbrella cover and a rack for attaching the cover.
- Cylindrical Volper-Grigorovich fungus - successfully compensating for pressure loss at the nozzle outlet. It consists of a lower glass, an upper glass with concave walls, a conical umbrella and mounts. The Volper fungus protects the ventilation system better from the wind than TsAGI.
- H-shaped pipe manifold It is an element of pipes in the form of the letter N. This rather bulky design completely protects against wind blowing, moisture, reverse traction, freezing. However, the traction design increases minimally.
- Weather vane cap when working, it always turns back to the wind, which prevents blowing inward. A zone of reduced pressure appears behind the nozzle body and the air stream quickly leaves the vertical channel. Effective for increasing traction, but poorly protects from rain.
- Turbo deflector - This is a spherical rotational deflector having many semicircular blades that rotate in the wind. A rarefaction appears inside the ball. Ineffective in calm weather.
One of the improved varieties of the traditional fungus on the pipe is the Astato-type static-dynamic device, which consists of 2 truncated cones, which are turned with their vertices facing each other. Above is an electric fan and an umbrella.
The system is effective even in complete calm. The only drawback is the high price.
When choosing a deflector, you need to consider:
- The nozzle size must be selected according to the diameter of the exhaust barrel. If the house has a rectangular shaft, you will have to use an adapter.
- TsAGI and the Volper deflector are maintenance free.
- In the absence of traction, it is better to set dynamic options for caps.
- When buying a rotating deflector, you need to choose more expensive models with a sealed bearing that does not freeze in winter.
- In areas with strong winds, it is better to choose an H-shaped deflector or turbo-reflector, for other climatic conditions - TsAGI.
If you have a budget in any region, you can install Astato. The device requires periodic maintenance.
TsAGI deflector can be assembled with your own hands. It is slightly different from the usual Grigorovich umbrella. The difference is only in the shell attached around the fungus
Let's look at how to properly install a ventilation hood on the roof. After the purchase, the model needs to be assembled and all the fasteners securely fixed. Then, when mounting the device on the pipe, you need to carefully drill holes for fastening. The device is fixed to screws or rivets. Additionally, you can put a clamp.
Roof Fan Features
Another element of the ventilation system is a roof fan.Using these devices, the waste polluted air is removed from the premises.
They are mainly designed to work in general ventilation systems without ventilation ducts, but they are also used with air ducts. The main advantage of roof fans is their use reduces the required length of air ducts.
In regions with low to medium wind loads, you can install an original and effective wind deflector. It will make the system work even with slight wind blows.
Options for roof fans vary in size, power, performance, sound pressure level.
The following common types can be distinguished:
- axial aerospace defense are installed on industrial buildings;
- BLOOD can be used in private homes;
- VKRM and VKR are connected to air ducts.
What are the advantages of roof fans?
- installation does not require a separate room;
- simple maintenance;
- hinged models make access to the main parts easier.
When choosing a roof fan, you need to pay attention to the performance of the model, the material of the housing, the method of power supply, the noise generated.
If there is no draft in the exhaust duct, the roof fan is a good solution to the problem. When using models with vertical discharge, air is thrown up sometimes up to several meters in height
Most products are manufactured as centrifugal or axial:
- An axial fan is used to pump low-pressure air masses. Gas when moving through the rotor does not change direction, moving along the axis of the engine.
- The centrifugal fan is equipped with special blades that distribute air on the sides, which further moves to the outlet.
The types of roof fans are divided in the direction of discharge. Horizontal exhaust fans are installed where the exhaust air is not polluted and there is no risk of mixing it with fresh air entering the house.
Roof fans can be installed on different types of roofs. The technology of the device node passage in a hard roof is simple. A technological opening is cut through in the ceiling, and a brick foundation for the fan is built on the ventilation shaft.
To simplify installation work, special glasses are used, which are sometimes supplied complete with fans. The glasses have holes on the mounting flanges and are attached to the roof with anchor bolts. The fan and the cup are flanged to the bolted joints.
Between the flanges should be a rubber gasket for greater tightness. The glass during installation should be exposed strictly vertically. The fan on the glass is mounted horizontally. After installation, possible clearances are removed with sealant. Then a steel apron is installed.
Large manufacturers of ventilation systems issue video instructions for installing on the roof and fastening supply and exhaust units, fittings, aerators, deflectors:
The arrangement of the exit through the roof to the roof of the ventilation pipe of the house should be approached with particular care. Indeed, in natural ventilation systems, the presence of traction in the system depends on the state of this unit.
Do not allow the pipe to rain or icing. Therefore, much attention is paid to sealing the assembly itself and installing protective additional parts. Similarly, the installation of supply devices is performed.